Xfinity cable stuck on welcome screen.
To do this, simply unplug your TV from the power outlet and then plug it back in. This should reset your TV and hopefully fix the issue. If restarting your TV doesn’t work, you can also try resetting your Xfinity receiver. To do this, press and hold the “Reset” button on the front of your receiver for about 15 seconds.
Xfinity cable box setup welcome screen When you turn on your TV, you see a blue screen with a message saying "One Moment Please, this channel should be available shortly." Cause This message will appear on the television in the event that you lose the signal coming from BendBroadband and going into your set-top box.If you're connected properly, manually restarting your modem will often restore internet connectivity — the easiest way to do this is by unplugging your cable ...Cable stuck on welcome screen. My cable box is stuck on the welcome screen. I’ve unplugged it numerous time, once for 3 hours, and nothing works. Archived post. New comments cannot be posted and votes cannot be cast. Hello u/BabaComm1981, thanks for reaching out for help on Reddit!
If you're connected properly, manually restarting your modem will often restore internet connectivity — the easiest way to do this is by unplugging your cable ...618 Messages. Hi @Stevejob. Thanks for making our team aware of your cable box issues. If the screen is still stuck, you may need to restart it manually. Let us know if your experience is still the same. We're here to help. I no longer work for Comcast. I am an Official Xfinity Employee.
Xfinity Flex stuck on Welcome Connecting to your entertainment experience. I recently received a Flex streaming device when I subscribed to Xfinity Internet service. The Flex box worked fine when the installer first configured it to connect via WiFi to the Xfinity-supplied Gateway. I have since purchased a Motorola MB8600 cable modem to replace ...Xfinity Comcast offers a wide range of services, from cable TV and internet to home phone and home security. With so many options, it can be difficult to know where to start when l...
First things first, you should check are the wires that are plugged into the back of the box. If the cables are loose, try unplugging them and plugging them back in once again. Make sure all the connectors are in as tightly as possible. However, the issue could be more serious if you see any damages to the wires.Next day it wasn’t working again, stuck on the reboot “Welcome” screen (restarting the box didn’t help). I chatted again with the Xfinity Assistant, who did something and fixed it. It’s been working for over a day now, including over night. ... They are supposedly mailing me a proper 4k capable cable/dvr box because the local xfinity ...Xfinity box frozen on welcome screen. Solved. I’ve never had this problem before in my 2 years, it’s stuck on the welcome screen and it was totally fine earlier in the day when I …The X1 boxes need a better, cleaner signal to the box than the old Motorola does. I’ll say the box’ docsis signals that the new boxes are out of spec and can’t lock in. Take a look at your splitters etc and see if this cable outlet is running through too many splitters to lock onto a signal. 0.Here’s how you can reset your TV: Locate the power button on your TV or the remote control. Press and hold the power button for at least 10 seconds. Release the power button and wait for the TV to turn off and then back on. Once the TV restarts, check if the “Welcome” message is displayed correctly.
2. Restart Your Flex Box. Restarting the Xfinity Flex box will remove temporary glitches and establish the connections. Soft Reset: Press and hold the power button on the device for a few seconds until it restarts. Power Cycle: Unplug the Flex box from the power source, wait about 60 seconds, and plug it back in.
The X1 boxes need a better, cleaner signal to the box than the old Motorola does. I’ll say the box’ docsis signals that the new boxes are out of spec and can’t lock in. Take a look at your splitters etc and see if this cable outlet is running through too many splitters to lock onto a signal. 0.
The Flex box hangs up on the "Welcome Connecting to your entertainment experience" screen. It has been stuck on this screen all day. I got info to come up on the bottom of the screen showing that it is connected toWiFi and showing it's MAC address. I am using an my own modem & router. Any suggestions to get it to finish setup.Apr 2, 2022 · First things first, you should check are the wires that are plugged into the back of the box. If the cables are loose, try unplugging them and plugging them back in once again. Make sure all the connectors are in as tightly as possible. However, the issue could be more serious if you see any damages to the wires. Here's the detailed steps to direct message us: Click "Sign In" if necessary. Click the "Direct Message” icon (upper right corner of this page) Click the "New message" (pencil and paper) icon. Type "Xfinity Support" in the to line and select "Xfinity Support" from the drop-down list.My cable box is stuck on a software update in progress, and it never goes past 0%. This started a few days ago and our tv screen shows a message saying to call customer service, and when we did the... Xfinity box frozen on welcome screen. Solved. I’ve never had this problem before in my 2 years, it’s stuck on the welcome screen and it was totally fine earlier in the day when I watched tv but when I turned it on it was stuck on the welcome screen. The wires were checked and all tightened and I restarted it by taking the power out. The Peer to Peer chat icon is located at the top right of the Community Forum page, clicking on the chat icon will allow you to initiate a chat conversation with us directly. Please ensure you are sending your message to our 'Xfinity Support' handle. Have two TVs on xfinity- main and bedroom. Bedroom is stuck on blue screen that reads “There ...I woke up this morning to my cable box stuck on the welcome screen (what it looks like when it updates every morning.) It will not move past that. I've unplugged and reconnected all of the plugs/cables multiple times, and I've tried to refresh/reset the box via the website.
Hello, @user_0d1246! Thanks for reaching out to us on our Forums! I hope you are doing well. If you are still having issues with your cable box you can try restarting it using the methods listed in the following link: Restart Your X1 TV Box. If you still find yourself having issues, please let us know and we can dig deeper into the issue.To send a direct message, please click on the chat icon in the top-right corner of the screen, and select "Xfinity Support" to initiate a live chat. Click "Sign In" if necessary. Click the "direct messaging" icon or https://comca.st/3J0ir1l. Click the "New message" (pencil and paper) icon. Type "Xfinity Support" in the "To:" line and select ...To do this, simply unplug your TV from the power outlet and then plug it back in. This should reset your TV and hopefully fix the issue. If restarting your TV doesn’t work, you can also try resetting your Xfinity receiver. To do this, press and hold the “Reset” button on the front of your receiver for about 15 seconds.I powered off and on again. 2. When powering off the Flex box, I also unplugged the HDMI cable. After doing these things, I powered the Flex back on, while the Flex was showing the initial Welcome screen, take a battery out of the remote and put it right back, press Voice button numerous times, and I finally got to the next setup menu.Click the "New message" (pencil and paper) icon. Type "Xfinity Support" in the "To:" line and select "Xfinity Support" from the drop-down list which appears. The "Xfinity Support" graphic replaces the "To:" line. Type your message in the text area near the bottom of the window. Press Enter to send it. 0. 0. Start Here. I’ve had my XG1v4 box ...
Cable stuck on welcome screen. Closed. My cable box is stuck on the welcome screen. I’ve unplugged it numerous time, once for 3 hours, and nothing works. Archived post. …
Jun 6, 2020 · Stuck on welcome screen. We had to unplug our TV and flex box for a few minutes, and when we plugged them in again, we got stuck on the welcome screen. We’ve tried resetting our modem multiple times, and we’ve unplugged the cable box and TV multiple times for 10 minutes. Nothing works. Our internet is fine but we can’t get the TV past the ... The "To:" line prompts you to "Type the name of a person". Instead, type "Xfinity Support" there - As you are typing a drop-down list appears. Select "Xfinity Support" from that list - An "Xfinity Support" graphic replaces the "To:" line. Type your message in the text area near the bottom of the window. Press Enter to send itSep 15, 2023 · To fix Xfinity stuck on the welcome screen, check if your connections are tight and right. Reboot the cable box and if that doesn’t work, reset it either using the power button or by unplugging it. Restarting the gateway could also fix the issue. I returned the box for a new one at the Xfinity store and it's working now. It had been a working for a few years but I turned the TV on one day and it was stuck on that screen. Despite getting a notice both in chat and on the phone that I would not be receiving a call back, I did get a call from an agent about 90 minutes later.There are two modes for your TV Box when there has been no activity for four hours. Power Saver Mode, which conserves your power, and Nap Mode, which does not save power. Your TV Box will automatically go into Nap Mode after four hours of inactivity if you do not have Power Saver on. At this time, there is no way to turn off Nap Mode.Unplug the TV cord for about 10 to 15 seconds then plug it back in. Note, that you can also restart the Box from the Help Menu on your remote control; To access the Help Menu, press the A button on your remote control, pressing OK will bring you to the Restart tile. Press OK again to select Restart, it might take a few seconds for the Xfinity ...Restart using the power cord. Step 1: Disconnect the cord connecting the cable box. Step 2: plug it back to restart. 3. Using the restore default button. Step 1: Click on the Power button. Step 2: hold the power and hold the buttons. Step 3: click the UP and DOWN buttons together.Unplug the TV cord for about 10 to 15 seconds then plug it back in. Note, that you can also restart the Box from the Help Menu on your remote control; To access the Help Menu, press the A button on your remote control, pressing OK will bring you to the Restart tile. Press OK again to select Restart, it might take a few seconds for the Xfinity ...Ultimately, the box never gets past the welcome screen. Background: This XG1 was offline for several months because the room is was installed was gutted/redone and now we are putting things back. Here are the troubleshooting steps I have taken: Reset the box 50+ times using several wait times after the power is pulled (5 seconds, 10 seconds, 30 ...Click the "New message" (pencil and paper) icon. Type "Xfinity Support" in the "To:" line and select "Xfinity Support" from the drop-down list which appears. The "Xfinity Support" graphic replaces the "To:" line. Type your message in the text area near the bottom of the window. Press Enter to send it. 0. 0. Start Here. I’ve had my XG1v4 box ...
Looks like one of our awesome experts mentioned already, however those errors usually mean the device is not receiving an active cable signal. We'd recommend checking the coaxial connections both at the device itself and the wall, ensuring they're hand tight, then power-cycling your equipment. You can find troubleshooting tips and tricks on …
Activation process. Enter the last four digits of any phone number listed on your Xfinity account. Use the number keys or directional pad on your remote to enter numbers. If you’re having trouble using the last four digits of a phone number, you can select the Verify another way button to verify via text message or by entering your account ...
My Xumo Streaming Box is Stuck on Settings Page : r/Comcast_Xfinity. Help! My Xumo Streaming Box is Stuck on Settings Page. I turned on my tv and this was there. You can’t get to the homepage or anything other than view the settings. I’ve tried unplugging and all of that but it’s just the settings page. I just got this streaming box a ...It is not a direct path to Shaw Support. Call 1-888-472-2222 to get help. It's possible that a service call will be necessary to replace the device. Or, for a replacement device to be shipped, via Canada Post, to you, for self-installation, and return of the current device. BlueCurve TV Player XG1V4 screen is stuck on "Welcome. Bienvenido. Unplug the power cord from both your X1 box/router, and the wall outlet. 3. Wait 30 seconds. 4. Plug the power cord back into both your X1 box/router, and the wall outlet. 5. You should now see the Xfinity welcome screen. If it doesn’t appear after a few minutes, restarting your television or X1 box may be necessary. One of the best ways to fix an Xfinity (X1) Flex stuck at the welcome screen is to restart the device. So, if you are not able to fulfill your entertainment cravings …All my apps are working on my xfinity apps except HBO MAX it will load then stop and get stuck with a purple screen and the HBO MAX logo it won’t go any further. I have tried everything. Plugging out the tv , plugging out the cable box , restarting the router and plugging it back out and in. Check parental , even deleting the local cache ...Our cable box keeps restarting on its own and then gets stuck on the black "welcome screen." This has been happening multiple times a day for the last couple months.Please help. Archived post. New comments cannot be posted and votes cannot be cast. Hey u/ Alzriso_Gardn this is not the experience we want you to have using our services.24.6K Messages. 4 years ago. @azbmiller wrote: Mine is also stuck on the Welcome Screen. Also doesn't appear to recognize the Voice Remote. I've tried A&D to unpair and various other pair options. Stuck on pop-up about unpairing remote but no way to get to the OK button. This box is unlike the others in my house. If your X1 or Xfinity Flex streaming TV Box is frozen on the Welcome screen, check your connections and attempt to restart it. If you have a wireless TV box or Xfinity Flex device, you can also try restarting your modem/gateway and try connecting using the WPS buttons on the TV Box or Flex device. My cable box is non responsive and stuck on screen saver. Yesterday I tried watching my secondary TV (it doesn't get used very often and has a XG2v2-P box) and when I turned on the TV, it was stuck on the screen saver and not responding to anything I push on the remote. I have tried to unplug the box multiple times and when it reboots, it …The "To:" line prompts you to "Type the name of a person". Instead, type "Xfinity Support" there. - As you are typing a drop-down list appears. Select "Xfinity Support" from that list. - An "Xfinity Support" graphic replaces the "To:" line. Type your message in the text area near the bottom of the window.
The blue screen says "preparing your box for new software..." and is followed by eight DOCSIS status tests, with the last being "Operational..." The results are either DONE or OK for all of the tests, although the answers are different for each every time I reset. I have tried to unplug for 30-60 seconds multiple times to no avail.All my apps are working on my xfinity apps except HBO MAX it will load then stop and get stuck with a purple screen and the HBO MAX logo it won’t go any further. I have tried everything. Plugging out the tv , plugging out the cable box , restarting the router and plugging it back out and in. Check parental , even deleting the local cache ...My Xfinity box had no prior problems but after a power outage at my house after the power resturned my Xfinity xg2v2-p box now flashes Blue and goes to the welcome screen. Then it flashes back and goes to the update screen where it is stuck at 0%. It keeps doing this cycle without any progress ever being made.Apr 17, 2020 · 1Pst on main X1 Box (DVR) Well, I am going to post this here since phone support is absolutely useless. Spent literally three hours on the phone with Comcast to resolve my DVR issue to no avail. About four days ago, my X1 DVR box died. Tried to turn on the TV and was greeted with the "Welcome" message and the LED display on the box said "boot". Instagram:https://instagram. le vel coupon codeis fine china worth anythingbowser funeral home broken bow ok180 cup revenue Hello, For over a week now our Xfininity X1 box has been stuck at ,"Welcome Powering Up. This may take a few minutes...". I've unplugged and plugged the system back in a few times. I've tried calling but never get through because everyone is working remote now. The phone message says that there is an outage in my area and they are working on it ... liberty bowl mapcraigslist garage sales grand rapids mi Yes indeed. If your other TV's have the same message then it would indicate a fault with the common variable between them (the cable service). On a user level what you can try is rebooting the cable box by unplugging its power cord for 10 seconds and then plugging it back in and letting it reboot. bundt cake sizes Connection problems can also contribute to the Xfinity box getting stuck on the welcome screen. Issues with the HDMI cable, for example, can prevent the box from establishing a proper connection with the TV, resulting in the welcome screen freeze. Similarly, problems with the internet connection, such as slow or unstable connectivity, …This can reset the cable box and resolve temporary glitches that may be preventing it from powering on. After waiting about 60 seconds, reconnect the box to allow it to reboot fully before attempting to turn it on again. steps to unplugged and re-plugged: Unplug the Xfinity cable box from the power outlet. Wait approximately 60 seconds.Our cable box keeps restarting on its own and then gets stuck on the black "welcome screen." This has been happening multiple times a day for the last couple months.Please help. Archived post. New comments cannot be posted and votes cannot be cast. Hey u/ Alzriso_Gardn this is not the experience we want you to have using our services.